| Model |
IW9167EH-ROW-AP |
| Software |
● Cisco IOS® XE Software Release 17.9.4 or later |
| Supported wireless LAN controllers |
● Cisco Catalyst 9800 Series Wireless Controllers (physical or virtual) |
| 802.11n version 2.0 (and related) capabilities |
● 4x4 MIMO with four spatial streams in one 2.4 GHz radio and two 5 GHz radios |
| ● Maximal Ratio Combining (MRC) |
| ● 802.11n and 802.11a/g |
| ● 20- and 40-MHz channels |
| ● PHY data rates up to 1.5 Gbps (with 40 MHz on both 5 GHz radios and 20 MHz on the 2.4 GHz radio) |
| ● Packet aggregation: Aggregate MAC Protocol Data Unit (A-MPDU) (transmit and receive), Aggregate MAC Service Data Unit (A-MSDU) (transmit and receive) |
| ● 802.11 Dynamic Frequency Selection (DFS) |
| ● Cyclic Shift Diversity (CSD) support |
| 802.11ac |
● 4x4 downlink MU-MIMO with four spatial streams on both 5 GHz radios |
| ● Maximal Ratio Combining (MRC) |
| ● 802.11ac beamforming |
| ● 20, 40, and 80 MHz channels |
| ● PHY data rates up to 3.4 Gbps (dual 4x4:4SS 80 MHz) |
| ● Packet aggregation: A-MPDU (transmit and receive), A-MSDU (transmit and receive) |
| ● 802.11 DFS |
| ● CSD support |
| ● Wi-Fi Protected Access (WPA) 3 support |
| 802.11ax |
● 4x4 uplink/downlink MU-MIMO with four spatial streams in 2.4, 5, and 6 GHz* |
| ● Uplink/downlink OFDMA |
| ● Target Wake Time (TWT) |
| ● BSS coloring |
| ● Maximal Ratio Combining (MRC) |
| ● 802.11ax beamforming |
| ● 20, 40, 80, and 160 MHz channels (IW9167E 5/6 GHz radio, IW9167I, IW9167E-STA and IW9167E-STA2 6 GHz radio) |
| ● 20, 40, 80 channels (5 GHz radio) |
| ● 20 MHz channels (2.4 GHz radio) |
| ● PHY data rates up to 7.8 Gbps (4x4 160 MHz on 6 GHz, 4x4 80 MHz on 5 GHz, and 4x4 20 MHz on 2.4 GHz) |
| ● Packet aggregation: A-MPDU (transmit and receive), A-MSDU (transmit and receive) |
| ● 802.11 DFS |
| ● CSD support |
| ● WPA3 support |
| Antennas |
● 8x N-type antenna ports |
| ● 1x TNC GNSS antenna port |
| ● Cisco offers the industry's broadest selection of antennas, delivering optimal coverage for a variety of deployment scenarios. |
| ● Supports Self-Identifiable Antennas (SIA) |
| Interfaces |
● 1x 100M/1000M/2.5G/5G Multigigabit Ethernet (RJ-45)/M12 X-code autosensing PoE+ in (802.3at/bt), UPOE in |
| ● 1x SFP (copper) 100M/1000M/10G Multigigabit Ethernet /M12 X-code OR 1x SFP (fiber) 1G/10G |
| ● Management console port (RJ-45) |
| ● Multicolor system LED |
| ● DC power input (micro-fit/M12 A-code) |
| ● Reset button |
| Note: PG 13.5 glands or M12 adapters shall be used with Ethernet and power interfaces to meet IP67 rating. |
| Note: Catalyst IW9167E-HZ has permanent M25 ports. M12 adapters are not compatible. See Installation Guide for gland requirements. |
| Dimensions (W x L x H) |
● 11.5 x 10.5 x 2.8 in (29.2 x 26.7 x 7.1 cm) |
| Weight |
● 9.2 lb. (4.2 kg) |
| Input power requirements |
● 802.3at (PoE+), 802.3bt (PoE++), Cisco Universal PoE (Cisco UPOE®) |
| ● DC power source: 24 to 48 VDC (maximum voltage range: 18 to 60 VDC) |
| ● Cisco power AC-DC power adapter, IW-PWRADPT-MFIT4P= |
| ● Cisco power injector, IW-PWRINJ-60RGDMG= |
| Surge |
● DC power input |
| ◦ EN50121-4, ± 2 kV (line-earth) and ± 1 kV (line-line) |
| ◦ AREMA, ± 1 kV (line-earth) and ± 1 kV (line-line) |
| ◦ CISPR35, ± 0.5 kV (line-earth) |
| ● Surge protection to ± 2 kV on Ethernet ports |
| ● Surge protection to ± 1 kV on SFP copper port with shielded cable |
| Environmental |
● Nonoperating (storage) temperature: -40° to +185°F (-40° to +85°C) |
| ● Nonoperating (storage) altitude test: +25˚C (77˚F), 17,000 ft. |
| ● Operating temperature: -40° to +158°F (-40° to +70°C) with solar load and still air. |
| ● Extended operating temperature (DC powered, not applicable to IW9167ESTA and IW9167E STA2): -58° to +167°F (-50° to +75°C) without solar loading, still air, and cold start limited to-40°C |
| ● Operating type test: +85°C for 16 hours |
| ● Operating humidity: 0% to 100% (condensing) |
| ● Operating altitude: 15,000 ft. (4,500 m) |
| ● Wind resistance: Up to 160 mph (257 km/h) sustained winds |
| Environmental ratings |
● EN/IEC 60529 (IP66 and IP67) |
| System memory |
● 2048 MB DRAM |
| ● 1024 MB flash |
| Available conducted transmit power settings (max/min), all antennas active |
2.4 GHz |
5 GHz |
5/6 GHz |
| ● 24 dBm (250 mW) |
● 30 dBm (1 W) |
● 23 dBm (200 mW) |
| ● -4 dBm (0.4 mW) |
● -4 dBm (0.4 mW) |
● -4 dBm (0.4 mW) |
Cisco Catalyst IW9167EH-ROW-AP đáp ứng các yêu cầu triển khai trong hệ thống giao thông và công nghiệp như thế nào?
Catalyst IW9167EH-ROW-AP được thiết kế đáp ứng nhiều tiêu chuẩn công nghiệp và giao thông như EN50121-4 và AREMA về khả năng chống nhiễu và chống xung điện. Kết hợp với khả năng hoạt động ở nhiệt độ lên đến 70°C (hoặc 75°C khi cấp nguồn DC), thiết bị phù hợp để triển khai trên hệ thống đường sắt, giao thông thông minh, nhà máy và các hạ tầng công nghiệp yêu cầu độ ổn định và độ tin cậy cao.
Tính năng Self-Identifiable Antennas (SIA) trên Cisco Catalyst IW9167EH-ROW-AP có ý nghĩa gì đối với công tác quản trị mạng?
Self-Identifiable Antennas (SIA) cho phép Access Point tự động nhận biết thông tin của ăng-ten Cisco được kết nối, bao gồm loại ăng-ten và các thông số kỹ thuật liên quan. Nhờ đó, bộ điều khiển có thể áp dụng cấu hình phù hợp, giảm nguy cơ cấu hình sai, rút ngắn thời gian triển khai và hỗ trợ quản trị viên dễ dàng kiểm tra, giám sát hệ thống từ xa.
Khả năng hỗ trợ ăng-ten của Cisco Catalyst IW9167EH-ROW-AP mang lại sự linh hoạt như thế nào khi triển khai mạng không dây?
Cisco Catalyst IW9167EH-ROW-AP được trang bị 8 cổng ăng-ten N-Type cùng 1 cổng TNC dành cho GNSS, đồng thời hỗ trợ Self-Identifiable Antennas (SIA). Thiết kế này cho phép sử dụng nhiều loại ăng-ten khác nhau phù hợp với từng môi trường triển khai, đồng thời giúp thiết bị tự động nhận diện loại ăng-ten được kết nối để giảm sai sót trong cấu hình và tối ưu hiệu suất phủ sóng.